Charnwood W030 Spindle Moulder

£748.99

SKU: Charnwood W030 Spindle Moulder Categories: , ,

Charnwood W030 Spindle Moulder

  • Cast Iron Main Table

  • Cast Iron Tenonning Table

  • Cast Iron Cutter Hood

  • 4 Speeds; Softwood, Hardwood, Routing, Sanding

  • Maximum Tooling Diameter 160mm

  • Independently Adjustable Fences

  • 100mm Diameter Extraction Outlet

Fitting neatly into the gap between the heaviest router table and an industrial sized spindle moulder this machine is ideally suited to small professional workshops.
A precision ground cast iron table, a steel base cabinet and a 2hp induction motor are the basic ingredients which make up this fantastic recently upgraded spindle moulder. The height of the spindle, which is a standard 30mm diameter, is controlled by the large hand wheel which can then be locked in position.

A simple belt change selects the correct spindle speed for the tooling. The new 4 speed version provides even more versatility;

  • 1500rpm – Drum Sanding *

  • 4500rpm – Moulding Hardwoods

  • 6500rpm – Moulding Softwoods

  • 8500rpm – Routing **

Fitting neatly into the gap between the heaviest router table and an industrial sized spindle moulder this machine is ideally suited to small professional workshops.

A precision ground cast iron table, a steel base cabinet and a 2hp induction motor are the basic ingredients which make up this fantastic recently upgraded spindle moulder. The height of the spindle, which is a standard 30mm diameter, is controlled by the large hand wheel which can then be locked in position.

A simple belt change selects the correct spindle speed for the tooling. The new 4 speed version provides even more versatility;

1500rpm – Drum Sanding *

4500rpm – Moulding Hardwoods

6500rpm – Moulding Softwoods

8500rpm – Routing **

The cutter hood is cast iron with a dust outlet at the centre providing efficient extraction for this machine which can produce a high volume of dust and chips. An extractor with 1000 cubic metres an hour airflow is recommended to cope.

The two aluminium fences are adjustable to set the width of the opening, to suit the cutters being used. The outfeed fence can also be stepped out, controlled by a fine pitch thread adjuster, for operations where the complete edge of the workpiece is being removed. Fully adjustable guards are connected to a hinged plate which can quickly be lifted to allow clear access to change the tooling.

The sliding carriage consists of a cast iron table with four bearing guides running along an aluminium extrusion. The fence angle can be set accurately between 90 and 45 degrees with a useful stop to quickly return to 90 degrees again. A hold down clamp and a length stop complete the equipment.

Supplied with sliding carriage, Set of spindle shims, 1/2″ Routing collet, adjustable height rubber feet, cable and plug.

Runs off any standard 13amp, 240v electric supply.

Specification

Motor (induction)            1500w, 240v

Main table size  600mm x 400mm

Sliding table size               400mm x 180mm

Spindle diameter              30mm

Speeds 4 (1500, 4500, 6500 & 8500rpm)

Vertical stroke   110mm

Table aperture diameter               160mm

Table aperture depth     50mm

Table height       870mm

Fence size           125mm x 700mm

Dust extraction outlet    100mm

Dimensions (WxDxH)     830mm x 1070mm x 1280mm

Weight 95kg

Rating   Light trade

Warranty             1 Year

 * Drum sanding kit is an optional accessory

Additional information

Weight 95.00000000 kg
Dimensions 83.00000000 × 107.00000000 × 128.00000000 cm
Power

Spindle Travel

Spindle Diameter

Spindle Height

Max Projection Over Table

Max Tool Diameter above Table

Max Tool Diameter Below Table

Table Height

Table Size

Extraction Outlet

Weight

Speeds

Reviews

There are no reviews yet.

Be the first to review “Charnwood W030 Spindle Moulder”